If your computer connects to the Modem/Router, then the Ooma Telo will connect also.flightconn wrote:Has anybody had any success using OOMA with a Motorola SBG6580. I have tried everything I have been told including eleminating the Modem/Router Firewall (it is a combo unit) and I just see the red OOMA symbol constantly.
Connect using a network cable, (try a different network cable then the one that was in the Ooma box) to the Ooma Telo Internet port, connect the other end of the cable to a Motorola SBG6580 LAN port.
Remove power from the Modem/Router and Ooma Telo.
Restore power to the Modem/Router. When the Modem/Router is done booting, restore power to the Ooma Telo.
You may have to wait up to an hour for Firmware downloads to finish before the Ooma symbol turns blue.
If this doen't work:
Leaving the Ooma Telo connected as instructed above, connect a network cable from the Ooma Telo Home port to the Wired LAN port of a computer. If Wi-Fi is turned on in the computer, temporarily turn Wi-Fi off in the computer. Reboot the computer. Access Ooma Setup by typing http://172.27.35.1 in the computer browser window. (Firefox works best for the browser). The Ooma Setup pages opens. Click on the Internet tab. Following the words Connection type: click on the down arrow and select Dynamic (DHCP).
Go to the bottom of the page and click on Update Device. Remove power from the Ooma Telo. Repower the Ooma Telo.
If these things don't work, try the Manual Ooma Telo Factory Reset procedure below:
Factory Reset Ooma Telo - Old Alternate Manual Procedure
1. Remove power from the Ooma Telo.
2. Repower the Ooma Telo.
3. Line 1 & Line 2 lights come on.
4. Line 1 & Line 2 lights go out and the Trash and Envelope lights come on for a very short period of time.
5. The Trash & Envelope lights go out and the bottom row (runway lights) starts scanning to the right.
6. When the scanning stops, the Ooma symbol will began flashing Red.
7. Press the Trash button, then the Stop button. Hold both the Trash and Stop buttons pressed until told to release.
8. The Ooma symbol will alternately blink Red and Blue.
9. The Ooma symbol will turn solid Red.
10. Release the Stop and Trash buttons.
11. Wait for a short period of time. The Ooma Telo will cycle back into a reboot.
12. After a successful Factory Reset, all Ooma Setup settings will be Factory.
If you are using an Ooma Wi-Fi dongle, you have to access Ooma Setup and rescan for the Wi-Fi network before a Wi-Fi connection can be made. The same is true for DSL, if you have to enter Connection type PPoE and a Name and Password for the Internet provider connection. You may want to reset MAC address to Use Built In, reset your Quality of Service Upstream/Downstream Internet Speed settings, and Bluetooth settings if you are using Ooma’s USB Bluetooth dongle. Ooma Telo handsets will have to be re-registered.
What I find interesting is everything else links up to this modem/router without a problem, I-pads, phones, laptop and a wired and wireless desktop, but not the ooma.
Any additional suggestions would be appreciated.
Is this a new installation?flightconn wrote:Has anybody had any success using OOMA with a Motorola SBG6580. I have tried everything I have been told including eleminating the Modem/Router Firewall (it is a combo unit) and I just see the red OOMA symbol constantly.
Did you activate the unit on the Ooma website BEFORE you connected it to the modem/router?
Telo with 2 Handsets, a Linx, and a Safety Phone
Telo2 with 2 Handsets and a Linx
Wish I knew for sure what step did it, but what i do know is that you helped - thanks so much