Got something else to discuss that is not covered by the previous forums? Post it here!
#70435 by donl1133
Thu Dec 09, 2010 10:33 am
I plan to go to warmer climate for a few months and will be in an RV park with wi-fi access. Am wondering if I can use my Telo down there with my laptop, and what I would need in addition to the laptop. I understand that a strong signal is needed for decent QOS, but will need some help with setting up the system. Anyone on this forum familar with this kind of setup and will it work? Thanks; Don
#70451 by thunderbird
Thu Dec 09, 2010 2:36 pm
Wireless Network Connection
(33.64 KiB) Downloaded 255 times

If you are going to use only Wi-Fi for your Internet connection, you may enable Internet Connection Sharing, in Wireless Network Connection Properties window, in your laptop computer’s Network control panel as shown int the attached PDF file, in the Window XP setup. (Other Microsoft Windows operating system settings are similar). Than all you need is a patch cable to be routed from the Ooma device to the (wired) network connection port on your laptop. When setting up, sometimes you have to disable and enable each Network Connection, starting with the wireless network connection first, than the local area connection next, and restart your computer to get everything to work right.
#70480 by donl1133
Thu Dec 09, 2010 6:03 pm
Thanks, Ibmofo and thunderbird for your responses. I will do a little more research of these things and hopefully be able to use my telo down there. Don
#70630 by lbmofo
Sat Dec 11, 2010 8:26 pm
Okay, I am really not too sure what the difference is between access point and bridge :?

Let's say I want to connect my Dish receiver (which only has an ethernet port and no wifi card) to my wifi network, what product do I need?

Could you find an inexpensive example product from Amazon?
#70633 by nn5i
Sat Dec 11, 2010 10:02 pm
Lbm, I was going to write a general tutorial, but -- looking at the original inquiry -- it would be a hijack of the thread, because it would have to be fairly long; it would be a disservice to the original poster. However, here's a little bit of explanation.

What he wants to do is make use of Internet services that are available through a wireless LAN, or WLAN. Because I find WLAN unpronounceable, I prefer to write out wireless LAN.

There are two kinds of Local Area Network: wired, and wireless. The Wi-Fi is just a wireless LAN that's made available for general use. The Telo (or Hub) can't connect to a wireless LAN; it requires a wired LAN.

Where did the Wi-Fi [I hate that term too] come from? The motel, or campground, or restaurant, has a wired LAN, to which they connect an access point, or AP. That's a device that makes the services (including Internet) of a wired LAN available to wireless devices, which are then called clients. Every Internet café, every Wi-Fi hot spot, has at least one AP installed; some have many APs.

Wireless devices, then, can connect to the AP and talk to it over the radio. The AP has a radio, and so does anything that connects wirelessly to the AP. When a wireless device connects to an AP and receives services, it is a client.

A PC with a wireless card in it is a client when you use it in an Internet café. If the PC doesn't have a wireless card but has an Ethernet port, it needs something else in order to become a client. A client bridge takes the wireless services available from an AP and converts them back to wired services.

A Telo has no wireless card in it, and can connect to the Internet only through an Ethernet cable. If the services are available only wirelessly, something must talk to the AP (over the radio) and relay information back and forth (over the wire). The Telo would then be a wired client, and the thing that connects this client to the wireless LAN is called a client bridge. In essence, a client bridge is the opposite of an AP.

Some devices (my routers, for example, with aftermarket firmware) can serve at either end of a wireless link (be an AP or a client bridge), but must be configured to be one or the other, not both. Most consumer devices, if running the manufacturer's firmware, are restricted to one or the other of these roles. That's because the manufacturer would like to sell you a new device whenever you need one for a different role. Alas.

Incidentally, a wireless router, very popular nowadays, is actually just a wired-only router that's built in the same box with an Access Point (AP). Usually it's a little cheaper than buying a separate router and AP, because the two essentially separate devices can share some hardware such as the power supply and the plastic enclosure.

Hope this helps. It seems to have grown long despite my original intention.

Anyway, to connect a Telo to a wireless LAN requires a client bridge to talk over the radio with the AP that created the wireless LAN.
#70642 by murphy
Sun Dec 12, 2010 3:41 am
The first item on this page is a client bridge. It connects to a device using a LAN cable to give it wireless capability. If the associated wireless router has WPS support, it connects by pushing a button on the device. If not, it has to be connected to a computer first to configure it. It will work with any device that has a LAN connection and needs wireless support. It's not only for a TiVo. It's expensive but it does the job. The cheaper third item on the page connects via a USB port and only works with a TiVo. ... index.html

Who is online

Users browsing this forum: No registered users and 7 guests